STEP TUTORIAL FOR BATHTUB INSTALLATION

Step Tutorial for Bathtub Installation

Step Tutorial for Bathtub Installation

Blog Article

Call Today

How do you actually feel on the subject of Tools You Need to Install a New Bathtub ?


Installing A Bathtub
Installing a bathtub isn't precisely rocket science, yet it does need strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately difficult project. If the old tub is easily available, the project can move easily; if you need to open up a wall surface to get rid of the old tub and place the brand-new bath tub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will need a helper to vacate the old bathtub as well as embeded in the new one. See to it you have actually qualified on your own for the task as well as fit attempting it. Rather than working with a specialist to take control of a halfway-completed project, it is better to take into consideration employing one prior to you start. Possibilities are you might require a professional plumber to make tube links.
This post will help you mount a new bath tub in your restroom if you have actually already gotten a brand-new tub and don't need to transform the plan of your previous supply of water pipes.
Your devices and product checklist must make up the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, activate the faucets to drain any water staying in the system. The process of removing the existing faucets can be quite troublesome due to the restricted gain access to that is commonly the situation.
    Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
    Prior to moving on to fit the new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end offers a connection to the existing supply pipelines.
    If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines are in area in between the tap as well as the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet connectors. The previous kind must be linked to the tap finishes initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Installing the Bath tub


    Using both wooden boards under its feet, position the tub in the required setting. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
    The next goal is to make sure that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the level reviews degree.
    To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
    Switch on the water system as well as check all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as likewise examine the overflow outlet and also the typical outlet for leakages.
    Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has actually been utilized at the very least once as this will certainly settle it right into its last setting.

    Preparing for the Installment


    Firstly, the supporting framework supplied with the bathroom must be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
    Fit the adaptable faucet adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
    Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its final position.

    Tiling Around the Bathtub


    In the area where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to break a rigid seal, triggering the water to penetrate the wall surface between the bathroom and also the tiling, bring about problems with dampness as well as possible leakages to the ceiling below.
    You can choose from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes as well as cartridges, and also can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the movement experienced when the tub is in usage. The sealer can crack fairly very early if you do not take into consideration this motion prior to sealing.
    Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or waterproof sticky and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    I was guided to that write-up about How to Install a Bathtub Yourself through a friend on our other domain. You should take the opportunity to distribute this blog entry if you enjoyed reading it. Thanks so much for your time spent reading it.


    Ring, relax, resolved!

    Report this page